View ICS9248-153_26371.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Integrated Circuit Systems, Inc.
ICS9248-163
Preliminary Product Preview
AMD - K7 System Clock Chip
Recommended Application: VIA KX133 style chipset Output Features: * 1 - Differential pair open drain CPU clocks * 1 - CPU clock @ 3.3V * 13 - SDRAM @ 3.3V * 6 - PCI @3.3V, * 1 - 48MHz, @3.3V fixed. * 1 - 24/48MHz @ 3.3V * 2 - REF @3.3V, 14.318MHz. Features: * Up to 166MHz frequency support * Support power management: CPU stop and Power down Mode from I2C programming. * Spread spectrum for EMI control ( 0.25% center spread). * Uses external 14.318MHz crystal
Pin Configuration
VDDREF REF0/CPU_STOP* GND X1 X2 VDD *MODE/PCICLK_F *FS3/PCICLK0 GND *SEL24_48#/PCICLK1 PCICLK2 PCICLK3 PCICLK4 VDDPCI BUFFER IN GND SDRAM11 SDRAM10 VDDSDR SDRAM9 SDRAM8 GND SDATA SCLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 REF1/FS2* GND CPUCLK GND CPUCLKC0 CPUCLKT0 VDDA PD#* SDRAM_OUT GND SDRAM0 SDRAM1 VDDSDR SDRAM2 SDRAM3 GND SDRAM4 SDRAM5 VDDSDR SDRAM6 SDRAM7 VDD48 48MHz/FS0* 24/48MHz/FS1*
* Internal Pull-up Resistor of 120K to VDD
48-Pin 300mil SSOP
Block Diagram
PLL2 /2 X1 X2 XTAL OSC PLL1 Spread Spectrum 48MHz 24_48MHz REF (1:0) CPUCLK
CPU DIVDER Stop
Functionality
FS3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 FS2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 FS1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 FS0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 CPU (MHz) 90.00 95.00 101.00 102.00 100.90 103.00 105.00 100.00 107.00 109.00 110.00 111.00 113.00 115.00 117.00 133.30 PCICLK (MHz) 30.00 31.67 33.67 34.00 33.57 34.33 35.00 33.33 35.67 36.33 36.67 37.00 37.67 38.33 39.00 33.33
CPUCLKC0 CPUCLKT0
SEL24_48# SDATA SCLK FS (3:0) PD# CPU_STOP# BUFFER IN
Control Logic Config. Reg.
PCI DIVDER
PCICLK (4:0) PCICLK_F
SDRAM DRIVER
SDRAM (11:0) SDRAM_OUT
9248-163 Rev A 9/22/00 Third party brands and names are the property of their respective owners.
PRODUCT PREVIEW documents contain information on new products in the sampling or preproduction phase of development. Characteristic data and other specifications are subject to change without notice.
ICS9248-163
ICS9248-163
Preliminary Product Preview
Pin Descriptions
PIN NUMBER 1 2 CPU_STOP#1, 2 3,9,16,22, 33,39,45, 47 4 5 6 7 MODE1, 2 8 10 13, 12, 11 14 15 17, 18, 20, 21, 28, 29, 31, 32, 34, 35,37,38 19,30,36 23 24 25 26 27 40 41 42 43 44 46 48 FS31, 2 PCICLK0 SEL24_48#1, 2 PCICLK1 PCICLK (4:2) VDDPCI BUFFER IN SDRAM (11:0) VDDSDR SDATA SCLK 24_48MHz FS1
1, 2
P I N NA M E VDDREF REF0
TYPE PWR OUT IN PWR IN OUT PWR OUT IN IN OUT IN OUT OUT PWR IN OUT PWR I/O IN OUT IN OUT IN PWR OUT IN PWR OUT OUT OUT OUT IN
DESCRIPTION REF, XTAL power supply, nominal 3.3V 14.318 Mhz reference clock.This REF output is the STRONGER buffer for ISA BUS loads This asynchronous input halts CPUCLKT, CPUCLKC & SDRAM (11:0) at logic "0" level when driven low. Ground Crystal input, has internal load cap (36pF) and feedback resistor from X2 Crystal output, nominally 14.318MHz. Has internal load cap (36pF) Supply for internal digital logic Free running PCI clock not affected by PCI_STOP# for power management. Pin 17, pin 18 function select pin, 1=Desktop Mode, 0=Mobile Mode. Latched Input. Frequency select pin. Latched Input. Internal Pull-up to VDD PCI clock output Logic input to select 24 or 48MHz for pin 25 output PCI clock output. PCI clock outputs. Supply for PCICLK_F and PCICLK, nominal 3.3V Input to Fanout Buffers for SDRAM outputs. SDRAM clock outputs, Fanout Buffer outputs from BUFFER IN pin (controlled by chipset). Supply for SDRAM 9nominal 3.3V. Data pin for I2C circuitry 5V tolerant Clock pin of I2C circuitry 5V tolerant 24MHz/48MHz clock output Frequency select pin. Latched Input. 48MHz output clock Frequency select pin. Latched Input Power for 24 & 48MHz output buffers and fixed PLL core. Reference clock for SDRAM buffer Powers down chip, active low Supply for core, & CPU 3.3V "True" clocks of differential pair CPU outputs. These open drain outputs need an external 1.5V pull-up. "Complementory" clock of differential pair CPU output. This open drain outputs needs an external 1.5V pull-up. 3.3V CPU clock output powered by VDDA 14.318 MHz reference clock. Frequency select pin. Latched Input
GND X1 X2 VDD PCICLK_F
48MHz FS01, 2 VDD48 SDRAM_OUT PD# VDDA CPUCLKT0 CPUCLKC0 CPUCLK REF1 FS21, 2
Notes: 1: Internal Pull-up Resistor of 120K to 3.3V on indicated inputs 2: Bidirectional input/output pins, input logic levels are latched at internal power-on-reset. Use 10Kohm resistor to program logic Hi to VDD or GND for logic low.
Third party brands and names are the property of their respective owners.
2
ICS9248-163
Preliminary Product Preview
General Description
The ICS9248-163 is a main clock synthesizer chip for AMD-K7 based systems with VIA style chipset. This provides all clocks required for such a system. Spread spectrum may be enabled through I2C programming. Spread spectrum typically reduces system EMI by 8dB to 10dB. This simplifies EMI qualification without resorting to board design iterations or costly shielding. The ICS9248-163 employs a proprietary closed loop design, which tightly controls the percentage of spreading over process and temperature variations. Serial programming I2C interface allows changing functions, stop clock programming and frequency selection.
Mode Pin - Power Management Input Control
MODE, Pin 7 (Latched Input) 0 1 Pin 2 CPU_STOP# (Input) REF0 (Output)
Power Groups
VDD48 = 48MHz, PLL2 VDDA = VDD for Core PLL, CPU VDDREF = REF, Xtal
Third party brands and names are the property of their respective owners.
3
ICS9248-163
Preliminary Product Preview
Serial Configuration Command Bitmap
Byte0: Functionality and Frequency Select Register (default = 0)
Bit
Bit 2, Bit 7:4
Bit 3 Bit 1 Bit 0
Description Bit Bit Bit Bit Bit CPUCLK PCICLK 2 7 6 5 4 (MHz) (MHz) 0 0 0 0 0 90.00 30.00 0 0 0 0 1 95.00 31.67 0 0 0 1 0 101.00 33.67 0 0 0 1 1 102.00 34.00 0 0 1 0 0 100.90 33.57 0 0 1 0 1 103.00 34.33 0 0 1 1 0 105.00 35.00 0 0 1 1 1 100.00 33.33 0 1 0 0 0 107.00 35.67 0 1 0 0 1 109.00 36.33 0 1 0 1 0 110.00 36.67 0 1 0 1 1 111.00 37.00 0 1 1 0 0 113.00 37.67 0 1 1 0 1 115.00 38.33 0 1 1 1 0 117.00 39.00 0 1 1 1 1 133.30 33.33 1 0 0 0 0 120.00 40.00 1 0 0 0 1 125.00 31.25 1 0 0 1 0 130.00 32.50 1 0 0 1 1 133.73 33.43 1 0 1 0 0 135.00 33.75 1 0 1 0 1 137.00 34.25 1 0 1 1 0 139.00 34.75 1 0 1 1 1 100.00 33.33 1 1 0 0 0 140.00 35.00 1 1 0 0 1 143.00 35.75 1 1 0 1 0 145.00 36.25 1 1 0 1 1 148.00 37.00 1 1 1 0 0 150.00 37.50 1 1 1 0 1 155.00 38.75 1 1 1 1 0 166.66 41.67 1 1 1 1 1 133.33 33.33 0 - Frequency is selected by hardware select, Latched Inputs 1 - Frequency is selected by Bit 2, 7:4 0 - Normal 1 - Spread Spectrum Enabled 0.25% Center Spread 0 - Running 1- Tristate all outputs
PWD Spread Precentage 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread 0.25% Center Spread
Reserved
0 1 0
Note: Default at power-up will be for latched logic inputs to define frequency, as displayed by Bit 3.
Third party brands and names are the property of their respective owners.
4
ICS9248-163
Preliminary Product Preview
Byte 1: CPU, Active/Inactive Register (1= enable, 0 = disable)
BIT
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Byte 2: PCI, Active/Inactive Register (1= enable, 0 = disable)
PIN#
40 43,44 46
PWD
X 1 1 X 1 X 1 1 FS2#
DESCRIPTION
(Reserved) (Reserved) FS3# SDRAM_OUT (SEL24_48#)# CPUCLK0 enable (both differential pair. "True" and Complimentary") CPUCLKT enable
BIT
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PIN#
7 13 12 11 10 8
PWD
X 1 1 1 1 1 1 1 FS0#
DESCRIPTION
PCICLK_F (Reserved) PCICLK4 PCICLK3 PCICLK2 PCICLK1 PCICLK0
Byte 3: SDRAM, Active/Inactive Register (1= enable, 0 = disable)
Byte 4: SDRAM , Active/Inactive Register (1= enable, 0 = disable)
BIT
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PIN#
26 25 17 18 20 21
PWD
1 1 1 1 1 1 1 1
DESCRIPTION
(Reserved) (Reserved) 48MHz 24_48MHz SDRAM 11 SDRAM 10 SDRAM 9 SDRAM 8
BIT
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
PIN# PWD
28 29 31 32 34 35 37 38 1 1 1 1 1 1 1 1
DESCRIPTION
SDRAM 7 SDRAM 6 SDRAM 5 SDRAM 4 SDRAM 3 SDRAM 2 SDRAM 1 SDRAM 0
Byte 5: Peripheral , Active/Inactive Register (1= enable, 0 = disable)
Byte 6: Peripheral , Active/Inactive Register (1= enable, 0 = disable)
BIT
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Notes:
PIN# PWD
48 2 1 1 1 X X 1 1 1
DESCRIPTION
(Reserved) (Reserved) (Reserved) MODE# FS1# (Reserved) REF1 REF0
BIT Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
PIN# -
PWD 0 0 0 0 0 1 1 0
DESCRIPTION R e s e r ve d ( N o t e ) R e s e r ve d ( N o t e ) R e s e r ve d ( N o t e ) R e s e r ve d ( N o t e ) R e s e r ve d ( N o t e ) R e s e r ve d ( N o t e ) R e s e r ve d ( N o t e ) R e s e r ve d ( N o t e )
1. Inactive means outputs are held LOW and are disabled from switching. 2. Latched Frequency Selects (FS#) will be inverted logic load of the input frequency select pin conditions.
Third party brands and names are the property of their respective owners.
Note: Dont write into this register, writing into this register can cause malfunction
5
ICS9248-163
Preliminary Product Preview
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V Logic Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND 0.5 V to V DD +0.5 V Ambient Operating Temperature . . . . . . . . . . . . . 0C to +70C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . 65C to +150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability.
Electrical Characteristics - Input/Supply/Common Output Parameters
TA = 0 - 70 C; Supply Voltage VDD = 3.3 V +/-5% (unless otherwise stated)
PARAMETER Input High Voltage Input Low Voltage Input High Current Input Low Current Input Low Current Operating Supply Current Power Down Input frequency Input Capacitance1 Clk Stabilization
1
SYMBOL VIH VIL IIH IIL1 IIL2 IDD3.3OP66 IDD3.3OP100 IDD3.3OP133 PD Fi CIN CINX
CONDITIONS
MIN 2 VSS-0.3 -5 -200
TYP
VIN = VDD VIN = 0 V; Inputs with no pull-up resistors VIN = 0 V; Inputs with pull-up resistors CL = 0 pF; Select @ 66MHz CL = 0 pF; Select @ 100MHz CL = 0 pF; Select @ 133MHz
MAX UNITS VDD+0.3 V 0.8 V A 5 A A 180 600 mA
VDD = 3.3 V; Logic Inputs X1 & X2 pins
12 27
14.318
16 5 45 3 125 100 500
A MHz pF pF
ms
Skew
1
1
TSTAB From VDD = 3.3 V to 1% target Freq. tCPU-SDRAM tCPU-PCI VT = 50% tCPU-AGP
-125 -100 -500
ps
Guaranteed by design, not 100% tested in production.
Third party brands and names are the property of their respective owners.
6
ICS9248-163
Preliminary Product Preview
Electrical Characteristics - USB, REF
TA = 0 - 70 C; VDD = 3.3 V +/-5%; CL = 20 pF (unless otherwise stated)
PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current Rise Time Fall Time
1 1 1 1
SYMBOL VOH5 VOL5 IOH5 IOL5 tr5 tf5 dt5
CONDITIONS IOH = -12 mA IOL = 9 mA VOH = 2.0 V VOL = 0.8 V VOL = 0.4 V, VOH = 2.4 V VOH = 2.4 V, VOL = 0.4 V VT = 50%
MIN 2.4
TYP
16
MAX UNITS V 0.4 V -22 mA mA 4 4 ns ns %
Duty Cycle
45
55
Guaranteed by design, not 100% tested in production.
Electrical Characteristics - CPUCLK (Open Drain)
TA = 0 - 70 C; VDD = 3.3 V +/-5%; CL = 20 pF (unless otherwise stated) PARAMETER Output Impedance Output High Voltage Output Low Voltage Output Low Current Rise Time Fall Time
1 1
SYMBOL ZO VOH2B VOL2B IOL2B tr2B tf2B VDIF VDIF VX dt2B tsk2B tjcyc-cyc2B tjabs2B
CONDITIONS VO = VX Termination to Vpull-up(external) Termination to Vpull-up(external) VOL = 0.3 V VOL = 0.3 V, VOH = 1.2 V VOH = 1.2 V, VOL = 0.3 V Note 2 Note 2 Note 3 VT = 50% VT = 50% VT = VX VT = 50%
MIN
TYP
MAX
UNITS V V mA
1
1.2 0.4
18 0.9 0.9 0.4 0.2 550 45 Vpullup(external) + 0.6 Vpullup(external) + 0.6 1100 55 200 250 +250
ns ns V V mV % ps ps ps
Differential voltage-AC1 Differential voltage-DC1 Differential Crossover Voltage1 Duty Cycle1 Skew1 Jitter, Cycle-to-cycle1 Jitter, Absolute1
-250
Notes: 1 - Guaranteed by design, not 100% tested in production. 2 - VDIF specifies the minimum input differential voltages (VTR-VCP) required for switching, where VTR is the "true" input level and VCP is the "complement" input level. 3 - Vpullup(external) = 1.5V, Min = Vpullup (external)/2-150mV; Max=(Vpullup (external)/2)+150mV
Third party brands and names are the property of their respective owners.
7
ICS9248-163
Preliminary Product Preview
Electrical Characteristics - CPUCLK
TA = 0 - 70 C; VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5%; CL = 20 pF (unless otherwise stated) PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current Rise Time Fall Time Duty Cycle Skew Jitter, Cycle-to-cycle Jitter, One Sigma Jitter, Absolute
1
SYMBOL VOH2B VOL2B IOH2B IOL2B tr2B tf2B
1 1
CONDITIONS IOH = -12.0 mA IOL = 12 mA VOH = 1.7 V VOL = 0.7 V VOL = 0.4 V, VOH = 2.0 V VOH = 2.0 V, VOL = 0.4 V VT = 1.25 V VT = 1.25 V VT = 1.25 V VT = 1.25 V VT = 1.25 V
MIN 2
TYP
19
MAX UNITS V 0.4 V -19 mA mA 1.6 1.6 ns ns % ps ps ps ps
d t2B1 tsk2B1 tjcyc-cyc2B1 tj1s2B1 tjabs2B1
45
55 175 250 150
-250
+250
Guaranteed by design, not 100% tested in production.
Electrical Characteristics - PCICLK
TA = 0 - 70 C; VDD = 3.3 V +/-5%; CL = 30 pF (unless otherwise stated) PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current Rise Time Fall Time
1 1 1 1
SYMBOL VOH1 VOL1 IOH1 IOL1 tr1 tf1 dt1 Tsk
1
CONDITIONS IOH = -11 mA IOL = 9.4 mA VOH = 2.0 V VOL = 0.8 V VOL = 0.4 V, VOH = 2.4 V VOH = 2.4 V, VOL = 0.4 V VT = 50% VT = 1.5V
MIN 2.6
TYP
19
MAX UNITS V 0.4 V -16 mA mA 2 2 ns ns % ps
Duty Cycle
1
45
55 500
Skew (window)
Guaranteed by design, not 100% tested in production.
Third party brands and names are the property of their respective owners.
8
ICS9248-163
Preliminary Product Preview
Electrical Characteristics - PCICLK_F
TA = 0 - 70 C; VDD = 3.3 V +/-5%; CL = 20 pF (unless otherwise stated) PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current Rise Time Fall Time
1 1 1 1
SYMBOL VOH1 VOL1 IOH1 IOL1 tr1 tf1 dt1 Tsk
1
CONDITIONS IOH = -11 mA IOL = 9.4 mA VOH = 2.0 V VOL = 0.8 V VOL = 0.4 V, VOH = 2.4 V VOH = 2.4 V, VOL = 0.4 V VT = 50% VT = 1.5V
MIN 2.6
TYP
12
MAX UNITS V 0.4 V -12 mA mA 2 2 ns ns % ps
Duty Cycle
1
45
55 200
Skew (window)
Guaranteed by design, not 100% tested in production.
Electrical Characteristics - 24MHz, 48MHz
TA = 0 - 70 C; VDD = 3.3 V +/-5%, VDDL = 2.5 V +/-5%; CL = 20 pF (unless otherwise stated)
PARAMETER Output High Voltage Output Low Voltage Output High Current Output Low Current Rise Time Fall Time
1 1 1 1
SYMBOL VOH5 VOL5 IOH5 IOL5 tr5 tf5 dt5 tj1s5 tjabs5
CONDITIONS IOH = -16 mA IOL = 9 mA VOH = 2.0 V VOL = 0.8 V VOL = 0.4 V, VOH = 2.4 V VOH = 2.4 V, VOL = 0.4 V VT = 50% VT = 1.5 V VT = 1.5 V
MIN 2.4
TYP
16
MAX UNITS V 0.4 V -22 mA mA 4 4 ns ns % ns ns
Duty Cycle
45 -1
55 0.5 1
Jitter, One Sigma Jitter, Absolute
1
1
Guaranteed by design, not 100% tested in production.
Third party brands and names are the property of their respective owners.
9
ICS9248-163
Preliminary Product Preview General I2C serial interface information
The information in this section assumes familiarity with I2C programming. For more information, contact ICS for an I2C programming application note.
How to Write:
Controller (host) sends a start bit. Controller (host) sends the write address D2 (H) ICS clock will acknowledge Controller (host) sends a dummy command code ICS clock will acknowledge Controller (host) sends a dummy byte count ICS clock will acknowledge Controller (host) starts sending first byte (Byte 0) through byte 5 ICS clock will acknowledge each byte one at a time. Controller (host) sends a Stop bit
How to Read:
Controller (host) will send start bit. Controller (host) sends the read address D3 (H) ICS clock will acknowledge ICS clock will send the byte count Controller (host) acknowledges ICS clock sends first byte (Byte 0) through byte 5 Controller (host) will need to acknowledge each byte Controller (host) will send a stop bit
How to Write:
Controller (Host) Start Bit Address D2(H) Dummy Command Code ACK Dummy Byte Count ACK Byte 0 ACK Byte 1 ACK Byte 2 ACK Byte 3 ACK Byte 4 ACK Byte 5 ACK Stop Bit
ACK Stop Bit ACK Byte 5 ACK Byte 4 ACK Byte 3 ACK Byte 2 ACK Byte 1 ACK Byte 0
ICS (Slave/Receiver)
How to Read:
Controller (Host) Start Bit Address D3(H) ICS (Slave/Receiver)
ACK
ACK Byte Count
Notes:
1. 2. 3. 4. 5. The ICS clock generator is a slave/receiver, I2C component. It can read back the data stored in the latches for verification. Read-Back will support Intel PIIX4 "Block-Read" protocol. The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode) The input is operating at 3.3V logic levels. The data byte format is 8 bit bytes. To simplify the clock generator I2C interface, the protocol is set to use only "Block-Writes" from the controller. The bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those two bytes. The data is loaded until a Stop sequence is issued. At power-on, all registers are set to a default condition, as shown.
6.
Third party brands and names are the property of their respective owners.
10
ICS9248-163
Preliminary Product Preview
Shared Pin Operation Input/Output Pins
The I/O pins designated by (input/output) on the ICS9248163 serve as dual signal functions to the device. During initial power-up, they act as input pins. The logic level (voltage) that is present on these pins at this time is read and stored into a 5-bit internal data latch. At the end of Power-On reset, (see AC characteristics for timing values), the device changes the mode of operations for these pins to an output function. In this mode the pins produce the specified buffered clocks to external loads. To program (load) the internal configuration register for these pins, a resistor is connected to either the VDD (logic 1) power supply or the GND (logic 0) voltage potential. A 10 Kilohm (10K) resistor is used to provide both the solid CMOS programming voltage needed during the power-up programming period and to provide an insignificant load on the output clock during the subsequent operating period. Figure 1 shows a means of implementing this function when a switch or 2 pin header is used. With no jumper is installed the pin will be pulled high. With the jumper in place the pin will be pulled low. If programmability is not necessary, than only a single resistor is necessary. The programming resistors should be located close to the series termination resistor to minimize the current loop area. It is more important to locate the series termination resistor close to the driver than the programming resistor.
Programming Header Via to Gnd Device Pad
Via to VDD 2K W
8.2K W Clock trace to load Series Term. Res.
Fig. 1
Third party brands and names are the property of their respective owners.
11
ICS9248-163
Preliminary Product Preview
PD# Timing Diagram
The power down selection is used to put the part into a very low power state without turning off the power to the part. PD# is an asynchronous active low input. This signal needs to be synchronized internal to the device prior to powering down the clock synthesizer. Internal clocks are not running after the device is put in power down. When PD# is active low all clocks need to be driven to a low value and held prior to turning off the VCOs and crystal. The power up latency needs to be less than 3 mS. The power down latency should be as short as possible but conforming to the sequence requirements shown below. CPU_STOP# is considered to be a don't care during the power down operations. The REF and 48MHz clocks are expected to be stopped in the LOW state as soon as possible. Due to the state of the internal logic, stopping and holding the REF clock outputs in the LOW state may require more than one clock cycle to complete.
PD#
CPUCLKT CPUCLKC
PCICLK VCO Crystal
Notes: 1. All timing is referenced to the Internal CPUCLK (defined as inside the ICS9248-163 device). 2. As shown, the outputs Stop Low on the next falling edge after PD# goes low. 3. PD# is an asynchronous input and metastable conditions may exist. This signal is synchronized inside this part. 4. The shaded sections on the VCO and the Crystal signals indicate an active clock. 5. Diagrams shown with respect to 133MHz. Similar operation when CPU is 100MHz.
Third party brands and names are the property of their respective owners.
12
ICS9248-163
Preliminary Product Preview
CPU_STOP# Timing Diagram
CPU_STOP# is an asychronous input to the clock synthesizer. It is used to turn off the CPU clocks for low power operation. CPU_STOP# is synchronized by the ICS9248-163. The minimum that the CPU clock is enabled (CPU_STOP# high pulse) is 100 CPU clocks. All other clocks will continue to run while the CPU clocks are disabled. The CPU clocks will always be stopped in a low state and start in such a manner that guarantees the high pulse width is a full pulse. CPU clock on latency is less than 4 CPU clocks and CPU clock off latency is less than 4 CPU clocks.
Notes: 1. All timing is referenced to the internal CPU clock. 2. CPU_STOP# is an asynchronous input and metastable conditions may exist. This signal is synchronized to the CPU clocks inside the ICS9248-163. 3. All other clocks continue to run undisturbed.
Third party brands and names are the property of their respective owners.
13
ICS9248-163
Preliminary Product Preview
SYMBOL
In Millimeters COMMON DIMENSIONS MIN MAX 2.413 0.203 0.203 2.794 0.406 0.343
In Inches COMMON DIMENSIONS MIN MAX .095 .008 .008 .110 .016 .0135
A A1 b c D E E1 e h L N VARIATIONS N 28 34 48 56 64
0.127 0.254 SEE VARIATIONS 10.033 7.391 0.381 10.668 7.595 0.635
.005 .010 SEE VARIATIONS .395 .291 .015 .420 .299 .025
0.635 BASIC 0.508 1.016 SEE VARIATIONS 0 8
0.025 BASIC .020 .040 SEE VARIATIONS 0 8
D mm. MIN 9.398 11.303 15.748 18.288 20.828 MAX 9.652 11.557 16.002 18.542 21.082 MIN .370 .445 .620 .720 .820
D (inch) MAX .380 .455 .630 .730 .830
Ordering Information
ICS9248yF-163-T
Example:
ICS XXXX y F - PPP - T
Designation for tape and reel packaging Pattern Number (2 or 3 digit number for parts with ROM code patterns) Package Type F=SSOP
Revision Designator (will not correlate with datasheet revision)
Device Type (consists of 3 or 4 digit numbers) Prefix ICS, AV = Standard Device
Third party brands and names are the property of their respective owners.
14
PRODUCT PREVIEW documents contain information on new products in the sampling or preproduction phase of development. Characteristic data and other specifications are subject to change without notice.

▲Up To Search▲

Price & Availability of ICS9248-153

	To Download ICS9248-153 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .